In early 2024, we floated a tender for a 2.8 MW distributed generation portfolio. Two manufacturers came back with quotes for 570W TOPCon modules. Same wattage. Same dimensions. Both offered a 25-year product warranty on paper. One quote sat about ₹0.35/W below the other.
My colleague glanced at the spec sheets and said what everyone in solar procurement says at that moment: "They're basically the same panel. Why are we overthinking this?"
He wasn't being careless. He was using the framework most buyers use: compare per-watt prices, match the headline specs, pick the cheaper option. It's the same framework I used when I first stepped into this role in 2019, managing a module procurement budget of roughly $5 million a year for a solar distribution business in Gujarat. (Should mention: that budget covers modules only—inverters and mounting structures sit in a separate cost center.)
That framework cost us money. Not on every order. But it compounded on a specific batch in 2022 in a way that changed our entire procurement policy. I've tracked every invoice in our system since then, negotiated with 20+ module manufacturers, and the pattern is clear enough to share.
The Oversimplification: 'Same Wattage, Same Panel'
A 570W module is a 570W module—until it isn't. It's tempting to reduce a photovoltaic panel to its power class, because that's the number on the datasheet, and datasheets are what we compare. But the power rating tells you very little about the materials inside the laminate or how that panel will behave in year 15.
Two modules from the same factory can be built to wildly different BOM (bill of materials). The solar cell grade, the encapsulant type, the frame thickness, the junction box brand, even the solder ribbon quality. These aren't aesthetic choices. They determine how a panel handles heat, humidity, microcracking, and potential-induced degradation.
And here's the uncomfortable part: two panels can have the exact same efficiency rating and identical temperature coefficients while using different materials underneath. The datasheet doesn't show you the BOM. The datasheet shows you what the manufacturer wants you to compare.
For the Indian market specifically, there's also regulatory qualification to consider—BIS certification and ALMM (Approved List of Models and Manufacturers) inclusion. Those are entry tickets, not differentiators. They don't tell you whether the encapsulant will survive 25 years of Gujarat summer. They tell you the panel met a minimum baseline, which is a lower bar than most procurement teams assume.
The OEM Blind Spot
This leads to the biggest blind spot I see in photovoltaic module buying: the assumption that a photovoltaic module OEM product is the same as a brand's own module if they come off the same production line.
I hear this logic constantly. "The same factory that makes Waaree solar panels also makes this private label, so it's the same panel—just cheaper without the brand premium."
The line doesn't determine the bill of materials. The purchase order does.
A manufacturer's own branded product line is typically built to a controlled spec sustained by their engineering team. When an OEM customer orders modules, they specify the BOM. That spec can be equal to the brand's own—or it can be spec'd down to meet a target price. Cheaper encapsulant. Less rigorous electroluminescence testing. A backsheet grade that handles UV exposure slightly worse over two decades. The line runs, the module gets produced, and it passes whatever QC threshold the OEM buyer paid for.
So yes, two modules can come off the same line in the same week. One carries the manufacturer's 25-year warranty and long-term degradation testing data. The other carries a private label brand you've never heard of, and the warranty obligation belongs to whoever is paying for the sticker—not necessarily the factory.
In 2023, I evaluated nine different private label proposals. Maybe eight, I'd have to check my spreadsheet. Exactly two could document the full BOM and name the entity actually holding the warranty liability. The rest offered a price advantage and a handshake.
The whole solar module OEM vs private label conversation usually comes down to one question: who wrote the spec, and who's accountable if the spec was wrong? If you're putting your name on a panel—or your clients' money behind it—you should know exactly what's inside.
What a 0.1% Degradation Difference Actually Costs
Now let's do the math that changed how I talk to our internal stakeholders.
Take a 570W panel. Module A has a linear degradation rate of 0.40% per year. Module B has 0.55%. That 0.15% difference sounds like the kind of number you file away and never revisit. It's not.
Year 25, Module A: approximately 513W. Year 25, Module B: approximately 490W. These are projections from the manufacturer datasheets, less initial-year degradation; exact values depend on test methodology. The gap is roughly 23W per module by the end of the term.
Scale that across a 2.8 MW installation of roughly 4,900 modules, and you're looking at more than 112 kW of missing capacity in year 25. At current tariff levels and load factors, that's not a rounding error—it's a six-figure revenue gap over the asset's useful life, in rupees and in energy terms.
The same logic applies to temperature coefficient and NOCT, but nobody quotes those in procurement meetings because they're harder to compare. The unit-price spreadsheet has no column for "what this panel will produce in year 20." And that is exactly the problem.
The 2022 Order That Changed Our Process
Back to 2022. We ordered 480 panels from a supplier who had arranged assembly through an OEM line at a well-known factory. The panels arrived, and the spec sheets matched what we asked for. The price was about 9% below our average buy-in for 540W modules at the time. We'd saved roughly ₹420,000 on that batch (about $5,500 at the exchange rate then).
Then the EL testing came back. We run electroluminescence imaging on a sample of every incoming batch—a QA step that costs us maybe half a percent of our module budget. It's the only way to see microcracks and cell damage that survive the lamination process but eventually kill a panel under thermal cycling. The sample showed microcracks in 3.2% of the panels. Not enough to fail a basic flash test. Enough to cut the realistic operational lifespan and raise hotspot risk.
Here's what the unit-price comparison didn't show: the panels had been built with a lower-grade encapsulant that the factory's own brand line didn't use. We only found out after pushing the supplier for the BOM, which took two months and a legal reminder.
The upside of that order was ₹420,000 in savings. The risk was unknown BOM quality. I kept asking myself: is ₹4 lakh worth potentially installing a hundred failing panels on a client's rooftop? The committee pressed for the cheaper quote. I let the urgency override the concern.
We rejected and replaced the batch. The rework cost, including freight and the price delta for replacement modules, came to roughly ₹590,000. The "savings" turned into a ₹170,000 net loss. And that's before counting our team's hours in the claim process.
Oh, and the really annoying part: the supplier's warranty was tied to their trading entity, which—as we learned during the dispute—was in the process of winding down. The factory had no contractual obligation to us. If we hadn't caught the microcracks before installation, we'd have been chasing a warranty claim against a company that no longer exists. (The warranty itself was technically valid. It was just worthless.)
What We Do Now—and What You Should Consider
So after tracking six years of orders and auditing our cost data, we rebuilt our photovoltaic module catalog selection process. It's not a "quote three vendors and pick the cheapest" model. It's a five-input TCO framework:
- Unit price—which I evaluate last, not first.
- Documented BOM—cell grade, encapsulant, backsheet, junction box, ribbon.
- Degradation coefficient and how it's verified.
- Warranty structure—who legally holds the liability, and will that entity plausibly exist in 2045?
- Delivery and claims history—what happens when a batch fails EL or visual inspection.
We also stopped treating private label as a dirty word. There are legitimate OEM programs, including ones offered by Waaree, where the buyer can lock the same BOM as the brand's own modules. The key is verification, not assumption.
When we evaluated the Waaree 570 watt solar panel for our catalog, the deciding factors were: the warranty sits with a listed entity with a substantial paper trail, the BOM transparency was enough for our engineers to sign off, and their OEM/private label process lets the buyer specify components rather than accept whatever the factory's cost engineer selected that quarter.
I should add that we don't buy every module from one supplier. Our catalog lists two manufacturers this year, and we allocate orders based on project specifics. But the 570W TOPCon module from Waaree holds a permanent slot because the TCO math works out—not because of a brand logo.
One more thing: the "always get three quotes" rule is fine as a baseline. It just ignores the transaction cost of vendor evaluation and the value of an established relationship where the factory already knows your QA standards. We still get three quotes. We just don't treat the lowest one as a decision.
The Bottom Line
Photovoltaic module procurement isn't a commodity purchase. The industry has spent years making modules look interchangeable—same size, same power class, similar efficiency. That's a marketing achievement. It is not a technical reality.
The cheapest quote wins only when you've verified that the BOM, the degradation data, the warranty backing, and the QC process are genuinely equivalent. In my experience managing 40+ supplier evaluations across seven years, that equivalence holds in maybe one in ten cases where a buyer defaults to the lowest per-watt price.
So next time someone tells you to compare solar modules by price per watt, ask what's inside the panel first. The price tag is the last number you should look at, not the first.